Bykski Full Coverage GPU Water Block and Backplate For GIGABYTE GeForce RTX 3080/3080ti/3090 GAMING/EAGLE/VISION/TURBO (N-GV3090GMOC-X
This full coverage block directly cools the video card core (GPU), graphics memory (RAM), and voltage regulator modules (VRM). By directly cooling these components, you can achieve great temperatures and reach higher overclocks or extend the overall lifespan of your card by running at below-factory temperatures.
The block is constructed of high-purity copper that is nickel electroplated to prevent oxidation. A high-flow design is used to allow multiple blocks to run in series. Top and bottom ports can be used to configure parallel or serial designs in multi-block setups.
Compatibility
-
Based on these GPU's (circuit board) designs only. Compatible with
GIGABYTE GeForce RTX 3080 TI GAMING OC 3X 12G
GIGABYTE GeForce RTX 3080TI EAGLE OC 12G
GIGABYTE GeForce RTX 3080TI VISION OC 12G
GIGABYTE GeForce RTX 3080TI TURBO 12G
GIGABYTE GeForce RTX 3080 GAMING OC 3X 10G
GIGABYTE GeForce RTX 3080 EAGLE OC 10G
GIGABYTE GeForce RTX 3080 VISION OC 10G
GIGABYTE GeForce RTX 3080 GAMING BOX
GIGABYTE GeForce RTX 3080 TURBO 10G
GIGABYTE GeForce RTX 3090 GAMING OC 3X 24G 24G
GIGABYTE GeForce RTX 3090 EAGLE OC 24G
GIGABYTE GeForce RTX 3090 VISION OC 24G
GIGABYTE GeForce RTX 3090 TURBO 24G - After narrowing your selection, Please check the entire PCB picture to ensure compatibility. If you have any questions, don't hesitate to contact support for confirmation.
- Fittings: G 1/4in. Thread
Parts Included
- 1x Full Coverage GPU Water Block
- 1x Backplate
- 2x Stop Fitting
- 1x Mounting Hardware
- Thermal grease
- 1x 5v A-RGB (RBW) Light
- (Warning: Addressable RGB (RBW) is 5V and is ONLY compatible with Addressable RGB (RBW) components. RGB is 12V and is ONLY compatible with RGB components. Mix and match will NOT work and will cause damage.
Warnings
This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.
Customer Reviews
I was very skeptical at first but very happy and satisfied with the purchase.
I didn't use any of the little plastic spacers sent with this block. No real instructions so i based the re installation based off of mostly how the original water block came off! But worked out great!
Very happy looks great even without the block and cpu block rgb inactive! Anyway so far stays under 40°C on average while gaming so i am very happy to keep my investment going! I still have yet to figure out the RGB out and for the CPU On Fire waterblock as well but both are fantastic and fit the build perfectly!
(Older components but first loop to give it a face lift!)
Mobo - z270e strix gaming
CPU - i76700k
GPU - Gigabyte Geforce RTX 3080 Gaming OC Waterforce V2. 10gb
Ram - Corsair Vengeance (2x16) 32gb
Memory - Samsung Evo 990 2tb
👍🤓
I replaced the stock water cooler for my GPU and this one has a noticable change in temps!
I purchased this for a Gigabyte rtx 3080TI oc. The block is 90% accurate for the card but leaves a few areas that were covered by the stock heatsink exposed (does not touch water block.) Otherwise my temps are good and installation was easy. 4/5 stars.
I am looking so forward to this becuase i had a front covered one, but it needed to be repaired and then the repair shop lost some screws so i can't put it together again.
This will hopefully take care of the little toasty memory on the back. 89 degrees is beginning to get a little toasty.
I hopw you all get what you are here for and whish you all the best.
Best Regards
Alex
So, this waterblock looks very nice, however it was not making proper contact with the GPU at all, due to the thermal pads being too thick. I was forced to re-use thermal pads for the time being from my stock cooler to try to get this waterblock to work, even then, my temps still run into the 80's. The thermal pads werent cut, all just default length. When buying a previous waterblock with a competitor, they had sent me 3 different baggies of 3 separate thermal pads, already pre-cut to fit perfectly, and instructions showing where to put each size of pad. This was not the case with this waterblock unfortunately. Going to try to reach out to customer support to get this resolved.
Using a Gigabyte 3080 Vision OC.
To view our comprehensive and detailed return policy, please kindly use the link provided below. This link will direct you to all the necessary information regarding our procedures, guidelines, and requirements for returns. You will find everything you need to know about the return process, including eligibility criteria, timelines, and any specific conditions that may apply. Thank you for your understanding and cooperation in this matter. We appreciate your attention to this important information.
Return/Refunds and Restock Fees
To view the full details of our shipping policy, please follow the link below. It includes important information regarding delivery times, available shipping options, and order specifics. If you have any additional questions or require help, feel free to reach out to us. Thank you for taking the time to review our policies.
Shipping and Delivery Policies