Excellent part. Fits great. Only works with their reservoir tubes. If you're getting a new pump, I would just get their entire armor/pump top combo. I had an issue with my first top, possibly due to my own mistake, and they replaced it immediately with no issues. Excellent service, and even better quality.
Cant install it yet because ram shortage is stupid. Product looks great. Please help consumers with fighting for ram! ):
the leds are already dying, the seal around the edge is drying out and I had to fix it for leaks
Review #2, I used this water block for about 4 months and I had to keep adding coolant to my build and never could find the leak until I uninstalled my GPU and noticed the leakage around the cooling plate. The fluid was leaking past the seal and down around the board. I had ordered two of these blocks for my system as I am running both of them on my new AM5 build and both of them are leaking. The leak however is much less on one than the other. These water blocks do work well and kept my GPU's cool but the slow leak around the seals are the deal braker for me. if it was only one card then I would have chucked it up to one of those 1 in a million things but both of them leaking tells me these blocks are not tested, just slapped together and shipped. I no longer recommend these blocks due to posable damage and loss of money.
This is a great radiator. You need to understand that it is thick and will likely not fit in any cases made today. the rad is like 4 inches thick. I had to get creative to install the rad next to its pump. The only donwside is the G1/2 ports. there are 6 of them and I could not for the life of me find fittings. I ended up getting a reducing adapter (G1/2 to G1/4, nickel plated too) but I had to get them from some industrial online shop that also advertised nuclear fittings for reactors and fittings for loops over 10,000 PSI. 10 of them cost me like a hundred bucks, so maybe making fittings that fit the radiator might be a good idea because otherwise theres no way to install this thing.
Bleeding the loop and filling was actually really easy but only because I have Leakshield and deltamate drain fitting. made the whole process super easy with very little trapped air. Overall, I think if I need it, I'd buy a second one. But in order to saturate the one rad, I'd need like 8 GPU's which is pretty unlikely.
Nice black hear spreads, though note you will need to buy extra 0.5mm thermal pads if your ram is dual rank. The thermal properties seem better than a normal ram heat spreader even without water cooling it.
The GPU block works perfectly.
I've never installed a GPU block or a custom loop for that matter, but I was successful in doing so.
Using the Bykski B-UL-D5-X-V4 Combo Water D5 Pump 100mm and some bykski tubing..
there's no leaking and it is quiet and cold.
I was expecting the worst, considering i've never done this before, but I have built many PCs so I remained confident.
It's clearly high quality, heavy and fits perfect.
It came in rich, expensive looking packaging..
If anyone were to ask if I recommend Bykski's water blocks. I'd say absolutely.
NO ISSUES.
My second Bykski GPU Cooler. I had bought my first to cool an RTX3090, which it also did well. On upgrade to an AMD platform, the 5070 was more than enough card, and this cooler fits perfectly. I enjoy the smaller form factor and weight. In a cooling loop with a Ryzen 9950 under a Corsair block, with a 6-fan push-pull arrangement on a 300mm radiator, I cannot get my coolant temp above 34C doing video editing, and 36C with stress testing. And the 5V ARGB strip in back works fine controlled by Corsair iCue, along with the rest of the fan-fare, makes the acrylic body more translucent. Assembly onto the fanless ASUS card was straightforward, intuitive without needing the instructions. Lighter than a full-width card, but you will still want to support its weight. Hint: counterbalance the card & block combined weight with the tubing, if design permits.
The liquid is thin and clear with nothing obvious suspended in it. And the bottle is perfect for handling it.
It's a large heatsink. Unsure why that is the case. It almost touches the SSD heatsink on the ASUSTUF Gaming B650-Wifi. But it looks good and it works great. Really enjoy BYKSKI products.
The i7-13700K is a heater and this sink didn't quite get it done. Due to power requirements, heat issues, etc. I chose to refactor my setup favoring an AMD solution that had comparable performance and lower wattage. I got a BYKSKI for the new rig and works perfectly.
Even though it went right on 5070 the fit was great the most important part was I needed the coolant ports on the end of the cooler as this is in a small form factor case. But it looks so good in there. It's not finished yet but couldn't have been a better choice.
More clear documentation would be nice but overall it's a pretty easy install if you have worked with water blocks before. Performs well knocked GPU temps from 75°C down to 45°C under full load.
grew up in idaho and only after i ordered saw that they are based there, which makes me even happier to report that the product is great and i'd recommend it to anyone.
I love the look of it just black metal rather than a bunch of RGB and plastic.
It has kept my GPU temps low even when full immersed in game. Best quality waterblock that I have purchased.
I love BYSKI waterblocks. there are easy to assemble and contain everything you need to install and get your system up and running.
Be careful were you locate this although it’s a very solid component the stiffness of the valve can lead to issues opening and closing if proper access is not available. 5 out of 5 though
It fits well how ever i wish you made a full cover water block back plate as well and sold them as a set.
Its a three rad dual pump system with chilled air its not pretty but functional!
